Redeem Your Black Friday Code: 75% Off All Exam Bundles! Use coupon code below! - Ends in 0d 00h 00m 00s - Coupon code: discactive

Netapp NS0-094 NetApp Hardware Support Engineer Professional Exam Exam Practice Test

Page: 1 / 8
Total 81 questions

NetApp Hardware Support Engineer Professional Exam Questions and Answers

Question 1

During a health check you observe that NetApp ONTAP software is reporting CRC errors on a network port from a node in the cluster.

Which component do you reseat?

Options:

A.

SFP

B.

cluster switch

C.

adapter

D.

data switch

Question 2

You have replaced a failed boot device. You perform boot_recovery and receive no errors. However, when the node reboots, it reports that it has no disks.

What are two possible causes? (Choose two.)

Options:

A.

The SAS cables were incorrectly reconnected after reinstalling the motherboard.

B.

The disks that are owned by this node have been marked as failed.

C.

The node is booting a lower version of ONTAP software than was last used.

D.

The interconnect is down.

Question 3

You have a NetApp ONTAP cluster that is serving both SMB over 10Gbe and FC data. An application owner has started to complain about poor performance and asks you to research the issue. When looking through EMS messages, you see the following output:

Question # 3

Which defective component triggers the EMS message?

Options:

A.

10Gbe module

B.

fiber cable

C.

32G FC module

D.

adapter card in slot 2

Question 4

On a NetApp FAS9000 system, which two field replaceable units (FRUs) are supported for replacement without takeover? (Choose two.)

Options:

A.

I/O module

B.

DCPM module

C.

caching module

D.

NVRAM module

Question 5

A node has panicked with a PCI/NMI error. Giveback has not been performed.

Which two commands should you run to collect the logs to determine the cause? (Choose two.)

Options:

A.

pelog –a –g=2

B.

show pci –v

C.

rdfile /mroot/etc/log/SSRAM

D.

event log show

Question 6

You need to upgrade your cluster switches to a new version of firmware.

Which command do you use to prevent automatic case creation?

Options:

A.

system node autosupport invoke -node * -type all -message STOP=5h

B.

system node autosupport invoke -node * -type all -message IGNORE=5h

C.

system node autosupport invoke -node * -type all -message MAINT=5h

D.

system node autosupport invoke -node * -type all -message SUPPRESS=5h

Question 7

You receive the following AutoSupport message:

[Node-01: cshmd: hm.alert.raised:alert]:

Alert Id = ClusterSwitchConnectivity_Alert

Alerting Resource = Node-02

raised by monitor ethernet-switch

[Node-01: mgwd: callhome.hm.alert.major:alert]:

Call home for Health Monitor process cshm:

ClusterSwitchConnectivity_Alert[Node-02].

[Node-01: mgwd: callhome.hm.alert.major:alert]:

Call home for Health Monitor process cshm:

ClusterSwitchConnectivity_Alert[Node-02].

When researching, you discover the following output:

Exhibit 2 — Network Port Health

Cluster::* > network port show

-health-status degraded

-fields health-degraded-reasons

node port health-degraded-reasons

-------- ---- -----------------------

Node-02 e0a link_flapping

What action do you take to resolve this issue?

Options:

A.

Replace the SFP on port e0a on node-02.

B.

Update the RCF file on the cluster switches.

C.

Update the firmware on the cluster switches.

D.

Replace the SFP on port e0a on node-01.

Question 8

Which two factors can increase the chances of experiencing a NetApp WAFL inconsistency on an aggregate? (Choose two.)

Options:

A.

ignoring NetApp Active IQ health risks

B.

constantly running at high load

C.

using outdated disk firmware

D.

upgrading frequently

Question 9

You are reviewing the output of disk show and one of the disks is reporting a container type of “unknown”.

What is causing this status?

Options:

A.

The disk is not owned by a member of the high-availability (HA) pair.

B.

The disk is failed.

C.

The disk is in the maintenance center.

D.

The disk does not have an owner.

Question 10

What should be the first step taken after detecting a NetApp WAFL inconsistency?

Options:

A.

Run wafliron.

B.

Stabilize the system.

C.

Force offline the affected aggregate.

D.

Run a dump to null.

Question 11

Which two tools can be used to recover an inconsistent aggregate? (Choose two.)

Options:

A.

file check

B.

wafl_check

C.

wafl snapiron

D.

wafliron

Question 12

At what stage is a write acknowledged to a client?

Options:

A.

when the write is present in the local node RAM and NVRAM

B.

when the write has been flushed to disk

C.

when the write is present in the NVRAM on the local node and its HA partner

D.

when the write has been flushed from NVRAM to RAM

Question 13

You have identified that the file named quarterly_25.docx is inconsistent.

Which nodeshell command reports whether there are Snapshot copies available?

Options:

A.

“priv set advanced; file check –f quarterly_25.docx”

B.

“priv set diag; file check –v < voiname > –i < field > ”

C.

“priv set diag; snap list –f quarterly_25.docx”

D.

“priv set advanced; aggr wafliron start –f quarterly_25.docx”

Question 14

Which type of AutoSupport message would you expect to see triggered automatically when ONTAP software detects a NetApp WAFL inconsistency on an aggregate?

Options:

A.

MEDIUM ERROR DURING RECONSTRUCTION

B.

CHECKSUM ERROR

C.

WAFL INCONSISTENT USER DATA BLOCK

D.

WAFL INCONSISTENT BLOCK

Question 15

What happens when the command diskcopy is run from nodeshell?

Options:

A.

It pre-fails a drive in an aggregate and copies it to a spare.

B.

It performs a low-level copy of the disk to another disk.

C.

It copies the disk content to a specified volume.

D.

It triggers a RAID reconstruction of that disk.

Question 16

Which command can you use to confirm successful completion of an ONTAP upgrade?

Options:

A.

system controller sp upgrade show

B.

cluster image show-update-progress

C.

job show –jobtype upgrade

D.

system node upgrade-revert upgrade-task –node < nodename > –version < ontap Version >

Question 17

You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After two days, you notice that the upgrade is causing issues. You decide to revert to ONTAP 9.5 software.

Which two actions do you need to complete before you revert? (Choose two.)

Options:

A.

Revert from ONTAP 9.7 software to ONTAP 9.6 software and then to ONTAP 9.5 software.

B.

Delete all Snapshot copies from the past two days.

C.

Reinstall your boot media and install ONTAP 9.5 software.

D.

Wipe your config and restore from backup.

Question 18

An NFS client is using nfs01_lif on homeport e0b on node1 for data traffic. After a head swap from node2, the administrator performs a takeover and notices that the client no longer has access to the data.

What caused the client to lose access to the data?

Options:

A.

The IPspace is configured for a CIFS workload.

B.

The subnet is configured to fewer IP addresses than necessary.

C.

The failover group is configured only with the e0b port from node1.

D.

There is no broadcast domain configured for NFS traffic.

Question 19

Which two NetApp tools should be used when troubleshooting the root cause of an unexpected controller reboot? (Choose two.)

Options:

A.

Active IQ Unified Manager

B.

Active IQ Digital Advisor

C.

ONTAP CLI

D.

ONTAP Mediator

E.

Active IQ Config Advisor

Question 20

A node has failed.

Which two conditions must be met for an automatic takeover to be triggered? (Choose two.)

Options:

A.

The combined utilization of both nodes must be less than 100%.

B.

The cluster network must be available.

C.

Mailbox disks must be reachable.

D.

NVRAM must be synchronized.

Question 21

Which two scenarios are common causes of the root volume needing root volume recovery? (Choose two.)

Options:

A.

The root volume ran out of space.

B.

The mainboard was replaced following a Non-Maskable Interrupt (NMI) panic.

C.

Root volume migrate was performed.

D.

The cluster configuration is out of sync on the volume.

Question 22

A new NetApp NS224 disk shelf is correctly cabled to a NetApp AFF HA pair. The disks show up as single-path.

Which action corrects the issue?

Options:

A.

Install iWARP capable PCIe cards to the system.

B.

Install RoCE capable PCIe cards to the system.

C.

Assign the disks to the new nodes.

D.

Set the storage port to -mode storage.

Question 23

Users are reporting slowness when accessing certain volumes with extremely high-performance requirements via NFSv3 on a four-node switched NetApp ONTAP cluster. Other volumes on the same cluster are behaving normally. Investigation reveals that there is a high amount of throughput recorded for the cluster LIFs.

What action enables you to determine which volumes are affected?

Options:

A.

View the active CIFS sessions on the cluster to determine the affected workloads.

B.

Check the NFS file locking lease period for the affected volumes.

C.

Review NFS export policies to ensure that client subnets are listed for the affected volumes.

D.

View the NFS connected client information and review the “Remote-Reqs” counter.

Question 24

Which two statements are true about an IOM 12 module? (Choose two.)

Options:

A.

It has two SAS ports.

B.

It has four SAS ports.

C.

It does not have an Ethernet port for alternate control path (ACP).

D.

It has an Ethernet port for alternate control path (ACP).

Page: 1 / 8
Total 81 questions