- Home
- Huawei
- HCIP-5G-RAN
- H35-581_V2.0
- H35-581_V2.0 - HCIP-5G-RNP&RNO
Huawei H35-581_V2.0 HCIP-5G-RNP&RNO Exam Practice Test
HCIP-5G-RNP&RNO Questions and Answers
A single measurement counter of the gNodeB can be part of multiple measurement subsets.
Options:
True
False
Answer:
AExplanation:
The intended answer is True because a gNodeB measurement counter may be associated with multiple measurement subsets or groupings within a performance-management implementation.
Performance measurement is essential for evaluating NR radio-network quality, identifying faults, monitoring resource utilization, and supporting optimization decisions.
A measurement counter represents an individual statistical quantity, such as the number of connection attempts, handover failures, successfully transferred data units, or occupied radio resources.
Measurement subsets provide logical groupings through which selected counters are organized and collected for particular operational purposes.
For example, a counter recording handover failures may contribute to a mobility-performance measurement subset and also be included in a broader service-quality measurement grouping.
This arrangement allows the same underlying statistical quantity to support different performance-analysis activities without requiring the network element to maintain entirely unrelated measurements for each report.
The counter's identity and measurement definition remain unchanged, even when it is referenced through several logical groupings.
However, the concepts of measurement counter, measurement subset, measurement job, and performance report must be distinguished. Their exact relationships depend on the performance-management data model and vendor implementation.
The updated question bank explicitly identifies this statement as true.
Official Reference: 3GPP TS 28.552, 5G Performance Measurements ; TS 28.550, Performance Management — Concepts and Requirements .
Technical warning / qualification: These standards establish 5G performance-measurement concepts, but the precise Huawei rule allowing one counter to belong to multiple measurement subsets has not been independently verified against the Huawei counter-configuration documentation.
Which of the following messages includes the reselection timer used for 5G-to-4G reselection?
Options:
SIB19
SIB5
SIB 24
SIB7
Answer:
BExplanation:
System Information Block 5 (SIB5) contains the inter-Radio Access Technology (inter-RAT) cell-reselection parameters required when a UE evaluates a transition from 5G NR to LTE E-UTRA.
In NR, cell reselection is performed primarily while the UE operates in RRC_IDLE or RRC_INACTIVE.
The UE evaluates serving-cell and neighboring-cell measurements according to broadcast frequency priorities, signal-level thresholds, and applicable reselection timers.
SIB5 provides information about E-UTRA carrier frequencies and their associated reselection parameters.
A particularly important parameter is t-ReselectionEUTRA , which specifies the timer associated with inter-RAT reselection toward LTE.
The UE applies this parameter when determining whether the configured reselection conditions have remained satisfied for the required duration.
This mechanism helps prevent excessive movement between NR and LTE cells caused by short-term radio-signal fluctuations.
SIB5 can also contain E-UTRA carrier-frequency lists, reselection priorities, signal thresholds, and speed-dependent reselection scaling factors.
The other listed SIBs are not responsible for carrying the standard NR-to-E-UTRA reselection timer.
Consequently, SIB5 is the correct answer because its information elements explicitly include the E-UTRA reselection configuration.
Official Reference: 3GPP TS 38.331, Section 6.3.1, SIB5 Information Element ; TS 38.304, Cell Reselection Procedures .
Which of the following PUCCH measurement counters is used for outer-loop power control on PUCCH?
Options:
SINR
Power spectrum density
RSRP
BLER
Answer:
DExplanation:
Block Error Rate (BLER) is the intended answer because outer-loop power-control algorithms use error-performance feedback to adjust the target received signal quality required for reliable control-channel reception.
PUCCH carries essential Uplink Control Information (UCI), including HARQ acknowledgments, scheduling requests, and configured channel-state reports.
Errors in these transmissions can produce unnecessary retransmissions, incorrect scheduling decisions, and reduced radio-network efficiency.
The distinction between inner-loop and outer-loop power control is important.
Inner-loop power control adjusts transmission power according to the difference between measured signal quality, commonly expressed through SINR, and a configured target.
The gNodeB can issue Transmit Power Control (TPC) commands to modify the UE's PUCCH transmit power.
Outer-loop power control adjusts the target signal-quality requirement according to observed error performance. When reception reliability deteriorates, the target SINR can be increased to improve decoding probability. Conversely, consistently satisfactory error performance can permit a reduction in the target.
RSRP measures received reference-signal power, while power spectral density expresses signal or noise power per unit bandwidth. Neither directly represents the error-performance feedback used in the intended outer-loop mechanism.
Therefore, BLER is the expected examination answer, with implementation-specific qualifications.
Official Reference: 3GPP TS 38.213, Section 7.2.1, PUCCH Transmit Power Control .
Technical warning / qualification: 3GPP specifies the PUCCH power-control signaling and calculations but does not mandate one universal BLER-based outer-loop algorithm. Huawei implementations may use BER or another error-performance measure depending on the radio technology and PUCCH configuration.
For the formula used to calculate PUSCH power during initial access, which statement about path loss (PL) is correct?
Options:
PL is an uplink path loss value estimated by a gNodeB.
PL is an uplink path loss value estimated by a UE.
PL is an uplink path loss value estimated by a UE.
PL is an uplink path loss value estimated by the gNodeB.
Answer:
BExplanation:
Who estimates it?
The UE estimates the path loss ( ), not the gNodeB.
Uplink vs. Downlink:
Because the UE does not know the uplink channel path loss directly prior to transmitting, it utilizes the channel reciprocity principle (or assumes average path loss symmetry).
The UE calculates the downlink path loss ( ) by taking the difference between the transmitted reference signal power broadcasted by the network (ss-PBCH-BlockPower or CSI-RS power) and the measured received power (higher-layer filtered RSRP):
Usage:
This estimated downlink path loss is then inserted into the open-loop power control formula to calculate the required uplink transmit power for PUSCH (including Msg3 during initial access).
During downlink data transmission, if a UE suddenly stops reporting CQI, which of the following issues will occur?
Options:
The downlink data transmission stops.
A low-order MCS index is always used.
The currently used MCS index is always used for data transmission.
No impact
Answer:
CExplanation:
CQI is part of the Channel State Information (CSI) reported by the UE to assist the gNodeB in downlink link adaptation.
The CQI value represents the estimated channel quality under configured reporting assumptions and helps determine an appropriate modulation order and coding rate.
When the UE stops reporting CQI, the scheduler loses an important source of updated radio-channel information.
In an implementation that retains the last valid channel-quality estimate, the scheduler may continue transmitting using the previously selected MCS.
However, this is not a universal requirement.
A gNodeB may also use HARQ acknowledgment statistics, observed decoding performance, configured fallback policies, or other available channel information to modify its scheduling decisions.
Consequently, downlink transmission does not necessarily stop, and a low-order MCS is not always selected.
The absence of fresh CQI can adversely affect link-adaptation accuracy and throughput, so option D is also not generally appropriate.
Option C therefore reflects the expected simplified behavior, but its use of the word always makes the statement technically overrestrictive.
Official Reference: 3GPP TS 38.214, Sections 5.1 and 5.2, PDSCH Procedures and CSI Reporting ; TS 38.321, HARQ Operation and MAC Procedures .
Technical warning / qualification: 3GPP does not mandate that an unchanged MCS must always be used after CQI reporting stops. The answer is valid only under a specific scheduler implementation or fallback policy. As written, the question has no universally guaranteed correct option.
Notification Control indicates whether the gNodeB must notify the core network when which of the following parameters can no longer be met?
Options:
Session-AMBR
GFBR
UE-AMBR
MFBR
Answer:
BExplanation:
The Guaranteed Flow Bit Rate (GFBR) is the correct answer because Notification Control enables the NG-RAN to notify the 5G Core when the guaranteed Quality of Service (QoS) requirements associated with a GBR QoS flow can no longer be fulfilled.
In the 5G QoS architecture, each QoS flow has a QoS profile containing parameters such as the 5G QoS Identifier (5QI), Allocation and Retention Priority (ARP), and additional bit-rate parameters where applicable.
For Guaranteed Bit Rate (GBR) QoS flows, GFBR specifies the bit rate that the network is expected to guarantee under the established QoS requirements.
When Notification Control is enabled, the NG-RAN evaluates whether the configured QoS characteristics remain achievable.
If the requested QoS profile cannot be satisfied, the NG-RAN can send a notification toward the Session Management Function (SMF) indicating that GFBR can no longer be guaranteed.
The standardized assessment may consider GFBR, Packet Delay Budget (PDB), and Packet Error Rate (PER).
The remaining parameters serve different purposes.
Session-AMBR limits aggregate bit rates for applicable non-GBR traffic within a PDU session.
UE-AMBR controls aggregate non-GBR traffic associated with the UE.
MFBR defines the maximum flow bit rate rather than the guaranteed flow bit rate.
Therefore, GFBR is the correct parameter.
Official Reference: 3GPP TS 23.501, Section 5.7.2.4, Notification Control .
Which NAS security encryption algorithms are supported by an RG?
Select All that Apply
Options:
Quantum encryption
SNOW 3G
ZuC
AES
Answer:
B, C, DExplanation:
SNOW 3G, ZUC, and AES are standardized ciphering algorithms supported within the 5G security architecture for Non-Access Stratum (NAS) protection.
NAS security protects signaling exchanged between the UE and the Access and Mobility Management Function (AMF), including registration, authentication-related procedures, mobility management, and applicable NAS transport messages.
3GPP TS 33.501 identifies three principal 128-bit non-null ciphering algorithm families.
128-NEA1 is based on SNOW 3G, a stream-cipher algorithm originally developed for mobile-network security applications.
128-NEA2 uses the Advanced Encryption Standard (AES) in Counter (CTR) mode.
128-NEA3 is based on ZUC, a stream cipher standardized for mobile telecommunications security.
The serving network selects a ciphering algorithm according to the UE security capabilities and the algorithms permitted by the network configuration.
Option A is incorrect because quantum encryption is not one of the standardized NAS ciphering algorithms defined in the referenced 3GPP specification.
An additional standardized option, NEA0, represents null ciphering, but it is not listed among the available answers.
Therefore, B, C, and D identify the applicable standardized non-null algorithm families.
Official Reference: 3GPP TS 33.501, Sections 5.11.1.1 and 5.11.2, Ciphering Algorithm Identifier Values and Requirements for Algorithm Selection .
Technical warning / qualification: The question uses RG without defining the abbreviation. The explanation verifies standardized 5G NAS ciphering algorithms, but whether a particular residential gateway supports all three depends on its implementation and advertised security capabilities. The wording should specify the intended gateway type.
In an NSA access issue, which of the following can cause a UE not to report B1 measurement results?
Select All that Apply
Options:
When the base station is close to the UE, the downlink power is oversaturated. As a result, the UE fails to detect cells.
The NR frequency configured on the LTE side is not the NR SSB frequency.
The UE measurement result does not meet the B1 threshold.
The NR cell status is abnormal.
Answer:
A, B, C, DExplanation:
All four conditions can prevent a UE from generating or transmitting a valid B1 measurement report during Non-Standalone (NSA) E-UTRA–NR Dual Connectivity (EN-DC) access.
In NSA architecture, the LTE eNodeB acts as the Master Node and configures NR inter-RAT measurements to determine whether an eligible 5G NR cell can be added as a Secondary Node.
Event B1 is triggered when the measured quality of an inter-RAT neighboring cell exceeds the configured threshold, subject to hysteresis and time-to-trigger requirements.
Option A: Excessive received signal power may saturate the UE receiver, degrading synchronization-signal detection and preventing successful NR cell measurements.
Option B: If the LTE-side measurement configuration identifies a frequency that does not correspond to the intended NR SSB carrier, the UE may be unable to detect the target NR synchronization signals.
Option C: If the measured NR signal does not satisfy the configured B1 entry condition, the reporting event is not triggered.
Option D: An abnormal NR cell may fail to transmit the required synchronization signals correctly or provide measurable radio coverage, preventing a valid measurement result.
Therefore, all four conditions are plausible causes of missing B1 measurement reports.
Official Reference: 3GPP TS 36.331, Inter-RAT Measurement Reporting — Event B1 ; TS 38.533, Section 8.4.2, NR Inter-RAT Event-Triggered Reporting Requirements .
A gNodeB can collect the causes of handover-preparation and handover-execution failures.
Options:
True
False
Answer:
AExplanation:
The statement is true because 5G NR performance-management procedures support the collection of handover failure statistics, including information that identifies failures during both handover preparation and handover execution.
The handover procedure contains distinct preparation and execution phases.
During handover preparation , the source gNodeB coordinates with the target gNodeB or the core network to prepare the necessary radio and session resources.
Preparation can fail because of resource-admission restrictions, incompatible configuration, transport-signaling problems, or other procedural errors.
Applicable NGAP and XnAP handover failure messages include cause information that can be recorded for network performance analysis.
During handover execution , the UE attempts to access the target cell and complete the required radio-connection reconfiguration.
Execution failures can occur because of radio-link problems, random-access failures, timer expiration, or unsuccessful completion of the mobility procedure.
The gNodeB can collect relevant failure statistics through standardized performance measurements and applicable signaling or UE failure reports.
3GPP TS 28.552 defines separate counters for unsuccessful handover preparation and execution, including failure-cause-specific subcounters.
These measurements assist operators in distinguishing admission-control problems from radio-mobility and execution problems.
Therefore, option A is correct.
Official Reference: 3GPP TS 28.552, Sections 5.1.1.6.1.3 and 5.1.1.6.1.9, Number of Failed Handover Preparations and Executions ; TS 38.423, XnAP Handover Procedures .
For both the VoNR and EPS fallback solutions, the 5GC must interwork with the IMS.
Options:
True
False
Answer:
AExplanation:
The statement is true because both Voice over New Radio (VoNR) and Evolved Packet System (EPS) fallback provide voice services through the IP Multimedia Subsystem (IMS), although the radio-access and core-network procedures used to deliver the voice session differ.
In a VoNR deployment, the UE maintains its connection to the 5G Core (5GC) through NR. IMS signaling and media traffic are transported over an appropriate PDU session, with the 5GC supporting QoS-flow establishment, policy enforcement, and connectivity to the IMS network.
The Session Management Function (SMF) manages the corresponding PDU session, while the User Plane Function (UPF) provides user-plane connectivity toward the IMS data network.
EPS fallback applies when the 5G system cannot provide the required IMS voice service directly over its existing radio access.
In this case, the 5GC and NG-RAN coordinate a handover or redirection toward LTE connected to the EPC. IMS voice establishment or continuation then takes place over the EPS.
Importantly, EPS fallback does not mean that the voice-media path remains anchored in the 5GC after fallback. It means that the 5G system participates in IMS voice-service support and coordinates access to EPS when necessary.
Official Reference: 3GPP TS 23.501, Sections 5.16.3.1–5.16.3.10, IMS Support and IMS Voice Service via EPS Fallback .
The NG interface between the 5G gNodeB and the core network is IP-network based. Which of the following protocols is used on the control plane?
Options:
SCTP
UDP
GTP-U
X2-C
Answer:
AExplanation:
Stream Control Transmission Protocol (SCTP) is the correct answer because it provides the transport-layer signaling service used by the NG control-plane interface between the gNodeB and the 5G Core.
In 5G Standalone (SA) architecture, the NG interface consists of two principal components: NG-C and NG-U.
NG-C connects the NG-RAN node to the Access and Mobility Management Function (AMF) and carries Next Generation Application Protocol (NGAP) signaling.
NGAP supports procedures such as initial UE message transfer, UE context management, handover coordination, paging, and PDU session resource management.
According to 3GPP TS 38.412, NGAP messages are transported using SCTP over IP.
SCTP provides reliable message delivery, multiple independent streams, congestion control, and multihoming capabilities.
These characteristics are particularly useful for maintaining signaling reliability and transport-network resilience.
The remaining options have different functions.
UDP provides connectionless transport and is used beneath GTP-U for applicable user-plane traffic.
GTP-U carries user-plane packets between the NG-RAN and UPF over the NG-U interface.
X2-C identifies the LTE X2 control-plane interface rather than the NG control-plane transport protocol.
Therefore, SCTP is the correct choice for the NG-C transport layer.
Official Reference: 3GPP TS 38.412, Sections 4.1 and 7, NG Signalling Bearer Protocol Stack and Transport Layer ; TS 38.410, NG Interface General Aspects .
Which of the following represents an availability KPI in NR system performance measurement?
Options:
PRB usage
Uplink/Downlink average cell throughput
Radio network unavailability rate
Uplink/Downlink traffic volume
Answer:
CExplanation:
Radio network unavailability rate is the correct answer because it measures the proportion of time during which a radio-network resource or service is unavailable for normal operation.
In NR performance management, Key Performance Indicators (KPIs) are classified according to the network characteristics they evaluate, including availability, accessibility, retainability, mobility, resource utilization, and traffic performance.
Availability KPIs assess whether network resources remain operational and capable of providing their intended services during the measurement period.
The radio network unavailability rate can be expressed conceptually as the ratio of accumulated unavailable time to the applicable observation period.
A lower unavailability rate indicates better network availability.
The remaining options represent different performance categories.
PRB usage measures the utilization of Physical Resource Blocks and is primarily a radio-resource utilization indicator.
Average cell throughput measures the rate at which data is successfully transferred during the relevant measurement interval, making it a capacity or throughput indicator.
Uplink/downlink traffic volume measures the amount of data carried by the network over a defined period.
Unlike these traffic and utilization indicators, radio network unavailability directly characterizes operational service availability.
Therefore, option C is the appropriate availability KPI.
Official Reference: 3GPP TS 28.554, Section 6.10.1, Availability KPI , including Cell Availability and Radio Access Network Availability; TS 28.552, 5G Performance Measurements .
Which of the following statements regarding throughput-related indicators is incorrect?
Options:
The measurement result is more accurate if the last small packet of each data transmission burst and its transmission duration are added.
The uplink/downlink average UE throughput is used to evaluate the user-perceived rate.
The average throughput of a single UE is obtained by dividing the data volume transmitted or received by the UE by the actual data transmission time.
The actual cell throughput can be obtained by dividing the total data transmission throughput within a measurement period by the time when data is transmitted in the cell.
Answer:
AExplanation:
Option A is incorrect under the standardized burst-based throughput measurement methodology because including the final small transmission interval can distort the measured throughput.
In NR performance management, throughput measurements are intended to represent radio transmission performance rather than the average application traffic rate across periods containing idle time.
The relevant measurement procedure distinguishes intervals during which the transmission buffer contains data from intervals when the buffer becomes empty.
The final transmission interval of a data burst may carry only a small residual packet. Including its duration and data volume can introduce a packet-size-dependent effect into the calculated throughput.
3GPP TS 28.554 therefore defines an extended throughput measurement method that excludes the final slot of the burst from the applicable calculation.
Option B is correct because average uplink and downlink UE throughput are used to assess radio-network performance as experienced by users.
Option C describes the general relationship between transmitted data volume and applicable active transmission time, subject to the precise measurement definitions.
Option D expresses a comparable throughput relationship at cell level, although its wording is less precise than the standardized KPI definitions.
Therefore, option A contradicts the specified throughput methodology.
Official Reference: 3GPP TS 28.554, Section 6.3.6.2, Extended Definition of Throughput , Figure 1; TS 28.552, 5G Performance Measurements .
Which of the following parameters are included in the measurement target IE of the 5G measurement configuration message?
Select All that Apply
Options:
Cell frequency
Serving cell offset
SMTC
SSB frequency
Answer:
A, C, DExplanation:
In 5G NR, Radio Resource Control (RRC) measurement configuration enables the UE to evaluate serving and neighboring cells for mobility, beam management, and radio-resource optimization.
Option A — Cell frequency: The intended parameter identifies the carrier frequency associated with the target cell or measurement configuration. This information allows the UE to determine the applicable frequency resources.
Option C — SMTC: SSB Measurement Timing Configuration specifies when the UE should perform SSB-based measurements. It defines the measurement-window periodicity, timing offset, and duration.
Option D — SSB frequency: The SSB frequency identifies the frequency location of synchronization signals that the UE must detect and measure.
Option B — Serving cell offset: Serving-cell offsets are used in measurement-event evaluation and reporting criteria. They are not part of the target-identification fields described by the intended question.
The standardized NR MeasObjectNR information element explicitly includes ssbFrequency and smtc1 , but does not define a separate field literally named Cell frequency within that structure.
Therefore, A, C, and D represent the intended Huawei-oriented answer.
Official Reference: 3GPP TS 38.331, Section 6.3.2, MeasObjectNR Information Element ; Section 5.5, Measurements .
Technical warning / qualification: The exact measurement target IE referenced by the question is not identified. While C and D are directly supported by the NR measurement-object specification, option A requires confirmation against the intended Huawei signaling definition. The answer is provisional rather than fully verified.
Which scenario requires a measurement-based SCG addition but does not allow blind SCG addition?
Options:
SCG addition after a handover
SCG addition after RPC connection reestablishment
Periodic SCG addition after network access
Initial SCG addition after initial access
Answer:
CExplanation:
Periodic Secondary Cell Group (SCG) addition after network access is the intended answer because the Huawei NSA procedure described in the material requires measurement-based SCG addition for subsequent periodic additions.
In E-UTRA–NR Dual Connectivity (EN-DC), the LTE eNodeB operates as the Master Node (MeNB), while the NR gNodeB operates as the Secondary Node (SgNB).
SCG addition allows the network to establish NR connectivity for a UE already connected to the LTE master network.
Huawei's implementation distinguishes measurement-based SCG addition from blind SCG addition.
In measurement-based addition, the MeNB configures the UE to measure neighboring NR cells. The UE reports eligible NR measurements, commonly through a B1 measurement-reporting procedure, enabling the network to select an appropriate NR secondary cell.
Blind addition does not require a fresh qualifying measurement report before initiating the corresponding addition attempt.
According to the supplied implementation description, blind addition is restricted to initial addition scenarios, including initial access, incoming handover, and incoming RRC connection reestablishment.
Periodic addition occurs after the initial addition opportunity and therefore requires measurement-based selection under this configuration.
Consequently, option C is the intended answer.
Official Reference: 3GPP TS 37.340, E-UTRA and NR Multi-Connectivity , topic Secondary Node Addition and Modification Procedures .
Which of the following MCS indices is required for 256QAM scheduling in downlink peak-rate testing?
Options:
MCS index 32
MCS index 27
MCS index 28
MCS index 23
Answer:
BExplanation:
MCS index 27 is the expected answer because it represents the highest non-reserved spectral-efficiency entry in the conventional NR PDSCH MCS table supporting 256QAM.
The Modulation and Coding Scheme (MCS) determines the modulation order and target coding rate used for scheduled data transmission.
For 256QAM, the modulation order is Q_m=8, meaning eight coded bits are mapped to each modulation symbol.
According to 3GPP TS 38.214, Table 5.1.3.1-2, MCS index 27 uses modulation order 8 and a target coding-rate parameter of 948/1024.
Its spectral efficiency is approximately 7.4063 bits per resource element before applicable resource overheads.
This makes index 27 particularly relevant when evaluating maximum downlink throughput under favorable radio conditions.
However, an important distinction exists between enabling 256QAM and achieving maximum spectral efficiency.
MCS index 23 also uses 256QAM, with a target coding-rate parameter of 797/1024 and a lower spectral efficiency of approximately 6.2266.
Therefore, both indices 23 and 27 can represent 256QAM modulation, but index 27 provides the higher nominal spectral efficiency.
MCS index 28 is reserved in the referenced table, while index 32 is outside the five-bit MCS index range.
Consequently, B is correct for maximum peak-rate testing.
Official Reference: 3GPP TS 38.214, Section 5.1.3.1, Table 5.1.3.1-2, MCS Index Table 2 for PDSCH .
Technical warning / qualification: Option D also represents 256QAM. The question is unambiguous only if peak-rate testing means selecting the highest non-reserved spectral-efficiency entry. The wording should explicitly state this condition.
Which of these statements about the downlink scheduling process are correct?
Select All that Apply
Options:
When the PRB usage is high, it is recommended that interference randomization be enabled to reduce interference.
The gNodeB determines whether to perform retransmission scheduling based on the HARQ feedback from the UE.
Downlink scheduling requires UEs to initiate requests.
The MCS index calculation during downlink scheduling mainly depends on CQI reporting.
Answer:
A, B, DExplanation:
Options A, B, and D represent the intended downlink scheduling principles described in the updated question bank.
Downlink scheduling is controlled by the gNodeB, which assigns radio resources and selects transmission parameters according to channel conditions, traffic demand, interference, and retransmission requirements.
Option A: Interference randomization can be used as an interference-management technique in heavily loaded radio networks. Its purpose is to reduce persistent interference effects by varying the relevant transmission or resource-allocation characteristics. However, enabling a particular Huawei interference-randomization feature at high PRB utilization is an implementation-specific recommendation.
Option B: The gNodeB uses HARQ acknowledgment information reported by the UE to determine whether transmitted downlink data has been successfully decoded or whether retransmission may be required.
Option D: Channel Quality Indicator (CQI) feedback provides information about the radio channel and supports Modulation and Coding Scheme (MCS) selection. Higher-quality conditions generally permit higher-order modulation and more efficient coding.
Option C is incorrect because downlink scheduling does not universally require an explicit scheduling request initiated by the UE.
The gNodeB already manages downlink data queues and can schedule available downlink traffic according to the configured scheduling mechanism.
Therefore, A, B, and D are the intended selections.
Official Reference: 3GPP TS 38.214, Sections 5.1 and 5.2, PDSCH Procedures and CSI Reporting ; TS 38.321, Section 5.3.2, Downlink HARQ Operation .
Technical warning / qualification: Options B and D are supported by standardized mechanisms. Option A is a vendor-specific optimization recommendation and requires confirmation against the Huawei scheduling feature documentation for the relevant release.
For NR coverage optimization, the principle is to preferentially optimize SS-SINR and then SS-RSRP.
Options:
True
False
Answer:
BExplanation:
Synchronization Signal Reference Signal Received Power (SS-RSRP) measures the received power of the synchronization-signal reference elements and is a fundamental indicator of NR radio coverage.
SS-RSRP optimization establishes whether the received serving-cell signal is sufficiently strong throughout the required coverage area.
Typical corrective actions include adjusting antenna azimuth, electrical downtilt, antenna height, reference-signal transmission characteristics, and site configuration.
Once acceptable signal-strength coverage has been established, the optimization process evaluates signal quality.
Synchronization Signal Signal-to-Interference-plus-Noise Ratio (SS-SINR) measures the synchronization-signal power relative to interference and noise.
Poor SS-SINR can occur even when SS-RSRP is strong, particularly in areas affected by overlapping cell coverage, excessive interference, or unsuitable beam configurations.
Interference coordination, antenna-pattern optimization, and mobility-parameter adjustments may improve SS-SINR and subsequent service performance.
The two measurements must ultimately be considered together because strong signal power does not guarantee acceptable radio quality.
However, the statement reverses the intended priority by placing SS-SINR before SS-RSRP.
Therefore, option B is correct.
Official Reference: 3GPP TS 38.215, Physical Layer Measurements ; TS 28.100, Annex A.1.3, Coverage Optimization Requirements and Measurements .
Technical warning / qualification: The sequence is a planning and optimization guideline, not an absolute 3GPP-mandated workflow. In an interference-limited network, SS-SINR may require immediate attention even when SS-RSRP is adequate.
Unlock H35-581_V2.0 Features
- H35-581_V2.0 All Real Exam Questions
- H35-581_V2.0 Exam easy to use and print PDF format
- Download Free H35-581_V2.0 Demo (Try before Buy)
- Free Frequent Updates
- 100% Passing Guarantee by Activedumpsnet
Questions & Answers PDF Demo
- H35-581_V2.0 All Real Exam Questions
- H35-581_V2.0 Exam easy to use and print PDF format
- Download Free H35-581_V2.0 Demo (Try before Buy)
- Free Frequent Updates
- 100% Passing Guarantee by Activedumpsnet